Witch Wine Label
Gift Ideas,  Halloween,  Machine Embroidery,  Quick Projects,  Twilly

Witch Wine Bottle Label with Patch Embroidery

Witch Wine Bottle Label

witch wine label

Create a fun label for any bottle to celebrate Halloween or general spookiness! This label features our Halloween Potions patch design, Witch Wine, but any of the patch designs in the Halloween Potions collections would be equally as charming. Grab the Twilly add-on pack to have tackle-twill fabric in the colors that coordinate with the design collection to create perfectly stitched patches that stand up alone or as appliqués.

Finished size: 4” x 10¼” with ½” closure overlap

WITCH WINE LABEL SUPPLIES

WITCH WINE EMBROIDERY

Import the medium Witch Wine design (for the 5×7 hoop) or a patch design of your choice that’s no larger than 3 ¾” x 5” into the embroidery machine.

Hoop two layers of Sulky Fabri-Solvy™.

fabri solvy in the hoop

Install a size 90/14 Embroidery Needle and thread the needle with the first thread color. Use Sulky Bobbin Thread in the bobbin.

If following the color chart for the Witch Wine design by Sulky, follow these instructions:

Stitch the first color stop, which are the placement stitches for the Twilly appliqué fabric.

witch wine placement stitches

Position the rectangle of Twilly fabric right side up over the placement stitches, completely covering them. Use KK 2000 to secure the Twilly to the stabilizer.

Stitch the next color stop, which are the tacking stitches for the appliqué fabric.

tacking stitches for witch wine applique

Remove the hoop from the machine or use the “Trim Position” function on the embroidery machine.

Using appliqué scissors, trim the fabric just beyond the placement stitches.

cut away Twilly around embroidery

Return the hoop to the machine or to the “Current Stitch Position.”

Continue embroidering the remaining design, stopping before the satin stitch edging step around the appliqué patch.

If using a different patch design and the satin edging doesn’t happen last, skip that step and embroider the remaining design. Then plan to go back to that step to attach the patch to the cork fabric, as detailed in “Witch Wine Appliqué.”

WITCH WINE APPLIQUÉ

Fold the cork fabric rectangle in half widthwise to find the center; mark with Wonder Clips.

Float the cork fabric UNDER the hoop, centering the desired appliqué placement.

float cork under witch wine patch

Stitch the last color stop of the Witch Wine design, or the satin stitch edging step of the chosen design.

stitch witch wine satin edge stitching

When the embroidery is complete, remove the hoop from the machine. Remove the stabilizer from the hoop, and then trim it close to the satin stitching perimeter. Be sure to not nick the cork fabric below the patch when trimming.

trim stabilizer beyond witch wine label patch

Use a saturated cotton swab to remove the excess stabilizer beyond the perimeter stitching.

remove stabilizer beyond patch

Set the patch aside to dry.

let witch wine label patch dry

WITCH WINE LABEL CONSTRUCTION

Place the quilting cotton rectangle and embroidered cork rectangle right sides together, matching all edges and corners.

Clip the perimeter, using Wonder Clips to avoid permanent pin holes.

Stitch the upper, lower and one side edge using a ¼” seam allowance.

stitch label perimeter

Clip the corners, being careful to not clip through the stitching.

clip corners of label

Turn the label right side out through the open side edge. Use a point turner to poke out the corners.

Turn the opening seam allowances to the wrong side; clip to secure.

clip open edge shut

Topstitch the label perimeter, closing the opening with the stitching.

topstitch label perimeter

Using a fabric marker, measure and mark two dots ¼” inside the right short edge, spaced equidistantly along the width. (Each dot should be about 1¼” from each long edge.)

mark snap placements on label

Use the snap setter and follow the manufacturer’s instructions to attach one male snap at each dot.

Wrap the label around a bottle of your choice to measure for the female snap placements.

wrap label around bottle

Install the female snaps.

witch wine female snaps

 

Wrap the label around the bottle and gift it to a friend or display at a party!

Print Friendly, PDF & Email

I am the Director of Content for Sulky of America. The former Editor in Chief of Sew News and Creative Machine Embroidery magazines, I hosted Sew it All TV on PBS for nine seasons. I've appeared on It's Sew Easy on PBS, DIY Network's Uncommon Threads, Hallmark's Marie Osmond Show, MacPhee Workshop and more! Come sew with me!

7 Comments

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.